Cookie Img
Home » Products » Textile Testing Equipment

Textile Testing Equipment

Optical Probes
close
Optical Probes
32
Optical Probes for thickness and distance measurements.. The measurement range of the chromatic optical probes reaches frome a few hundreds of microns up to millimeters allowing you the perfect tune to your applications High numerical aperture and small spot diameter are ideal for the most uses in metrology. The interferometric optical probes show off …
Gurley Cobb Absorption Testers
close
Gurley Cobb Absorption Testers
35
The standard for liquid absorption testing Purpose of list Water absorptiveness of paper board or other materials is a function of various characteristics such as sizing, porosity, etc. The Gurley-Cobb sizing test can be used to test absorption or resistance to absorption of water, oil and other liquids.
Carver has developed the following press which is specially configured to perform the compression molding of test plaque or bar specimens of Type I, II, III or IV polyethylene and other thermoplastic resins. The procedure is in conformance with ASTM Method D 1928, Procedure C. The press is equipped with heating/cooling platens and a programmable digital controller which has a heating/cooling loop for each platen and built-in program for the required 15°/minute ±2°C cooling rate. No. 37…
Manometric Gas Permeation Analyzer
close
Manometric Gas Permeation Analyzer
Lyssy L100-5000
A versatile gas analyzer for measuring the permeability of any common gas or gas mixture through films and foils. Typical gases measured include air, oxygen, nitrogen, carbon dioxide, hydrogen and helium. This instrument utilizes the manometric principle one of the most recognised gas permeability testing methods – pressure change via gas transmission through films. With two measuring chambers, ease of operation through the alpha-numeric keyboard and digital di…
Laboratory Sealer SGPE 3000
close
Laboratory Sealer SGPE 3000
SGPE 3000
Laboratory sealing equipment to make sealing welds using a thermal contact heat sealing technique with exactly defined parameters(sealing time, upper sealing temperature, lower sealing temperature and sealing force). Suitable for all heat sealable films such as Polypropylene, etc. or heat seal compatible compound materials such as coated aluminum films,…
Moisture Analyzer
close
Moisture Analyzer
36
Introducing Omnimark’s new Mark3 Moisture Analyzer The principle of operation of the Mark 3 is loss on drying. The instrument finalizes on a programmed rate of weight change compared to the actual initial weight of the sample over a programmed window of time. The Mark 3 analyzer is compared to a convection oven, vacuum oven or Karl Fischer titration to verify accuracy and precision. Accuracy is stated by the average of repeat tests compared to the standard AOAC or ASTM reference value while precision is established by the standard deviation of repeat tests on the Mark 3.
Universal Materials Testing Machine
close
Universal Materials Testing Machine
1kN Model
The M100-1 CT is a small footprint, single column, computer controlled universal materials testing machine using Testometric’s feature-rich winTest™ Analysis software running under the Windows™ operating system. Test setups are fully configurable and simple or more complex multi-stage test routines are controlled using the standard PC serial interface.
Permeometers
close
Permeometers
Model 4301
The Gurley Model 4301 Permeometer measures the porosity or air-permeability of materials where air flow is an important characteristic relative to their use. These materials might be non-woven or woven textiles, filter and cloth felts, some types of blotting, saturating and absorbent bag papers as well as meshes. Conform to TAPPI T-251, ASTM D-737, DATM 70.0-70 and ISO 5636/1.
Automatic Moisture Analyzer
close
Automatic Moisture Analyzer
37
Out of the box solution at your fingertips! Fast and accurate moisture or solids measurement with the Mark 3 LTE allows adjustments to be made in the processing cycle in minutes rather than hours. One button operation to perform a test. No pre-programming required on the part of the operator. Thousands of material program settings already established for the following markets: Pharmaceutical Food Chemical Wastewater Cosmetics Ethanol Pulp and paper Paint and coating…
Materials Testing Machine
close
Materials Testing Machine
2.5kN Model
The M250-2.5 is a small footprint, single column, computer controlled universal materials testing machine using Testometric’s feature-rich winTest™ Analysis software running under the Windows™ operating system. Test setups are fully configurable and simple or more complex multi-stage test routines are controlled using the standard PC serial interface.
Oxygen Permeation Analyzer
close
Oxygen Permeation Analyzer
8200
Simple, cost effective oxygen permeation testing for packages and bottles Ideal for oxygen permeation testing of containers, canisters, pouches, bags, closures and more. This two station analyzer is the economical solution. It incorporates the reliability and wide measurement range of our leading permeation instruments but is designed to be cost effective. The removable adapters offer a range of testing methods and can even be tailored to a specific requirement. It has the ability to evaluate a wide variety of barrier alternatives and their corresponding perf…
Bench Top Presses
close
Bench Top Presses
31
Bench Top Laboratory Presses from Carver, Inc. Automatic Lab Presses from Carver Include Auto Pellet and Standard Automatic Presses
ASTM Rubber
close
ASTM Rubber
28
Genesis Hydraulic Compression Press for Rubber Testing in Accordance with ASTM D3182. The Genesis Series Hydraulic Compression Press, Model G50H-19 ASTM is specially designed to vulcanize rubber sheets to provide samples for quality control, research and development and material comparison to prepare sheets for material property testing in accordance with ASTM D3182.
Capillary Rheometer
close
Capillary Rheometer
LCR 7000 Series
All digital calibration Increased speed and force range Advanced electronics and software enable up to 45 shear stress or shear rate data points per test Unique algorithms for polymer melt stability Bi-directional communications enable test parameters to be downloaded from the PC Multiple barrel heating zones and adaptive PID temperature control algorithm provide precise and u…
Labormaster 3000
close
Labormaster 3000
3000
The KOPP-LABORMASTER 3000 with integrated Laboratory-Sealer SGPE 3000 is made for measurement of sealing strength (strength of hot sealing and cold sealing / hot-tack and cold-tack). Exact sealing results, test of sealing strength, visualization, documentation and data logging are possible by using the KOPP-Labormaster 3000.
Optical Sensor
close
Optical Sensor
M10
Optical Sensor: Distance and thickness measurement with 10 channels The optical sensor CHRocodile M10 offers up to 10 independent measuring chanels. They can be used to measure the distance to any surface as well as the thickness of transparent materials.
Oxygen Permeation Analyzer
close
Oxygen Permeation Analyzer
8001
Modular systems for precision oxygen analysis of packaging film barriers. The 8001 is a versatile and easy to operate oxygen permeation analyzer with 2 stations for testing films or packages. Offering the highest quality coulometric oxygen sensor in the market with the lowest replacement cost, this instrument provides extremely fast purge down times and accurate readings at the lowest levels. With widest measurement range in the market, this analyzer can…
29
Genesis Series Hydraulic Presses from Compression Molding of Rubber, Plastics, Composites and Laminating: In 15 to 150 Ton Capacities Genesis Series presses are state-of-the-art hydraulic presses for compression molding of rubber, plastics and composites; also for laminating. The Genesis Series reflects more than a half century of WABASH leadership in hydraulic press design and construction. It is rugged enough for a round-the-clock performance on the production floor, but works equally well as a precision laboratory press. Genesis hydraulic lab presses are available in 15 through 150 ton capacities. The hydraulic system produces
Hydraulic Universal Testing Machine
close
Hydraulic Universal Testing Machine
5kN Model
The M350-5 range of twin column, computer controlled universal materials testing machine using Testometric’s feature-rich winTest™ Analysis software running under the Windows™ operating system. Test setups are fully configurable and simple or more complex multi-stage test routines are controlled using the standard PC serial interface.
CHRocodile LR
close
CHRocodile LR
LR
Very high lateral resolution to measure intricate structures. Optimized for inline measurement of thick foils.
Flow Characterization Rheometer (FCR)
close
Flow Characterization Rheometer (FCR)
FCR
Unique dual capillary design On-line ASTM D1238 melt flow rate at two load conditions Ideal for flow ratio measurements On-line apparent viscosities over broad shear rate range On-line measurements of polymer extensional properties Customer specified solutions Compact measuring head for close extru…
Oxygen Transmission Rate Tester
close
Oxygen Transmission Rate Tester
8700 and 8701
The ultimate solution for fast and reliable oxygen permeation testing of multiple bottles, packages or films. 8700 oxygen permeation analyzer The 8700 with fixed platens is ideal for rapid permeation testing of multiple bottles in PET bottle manufacturing and as an invaluable R&D resource in laboratories for development work to test and validate new packages. In addition, this analyzer can be used for Quality Control, to co…
Universal Tensile Testing Machine
close
Universal Tensile Testing Machine
10kN Model
The M350-10 range of twin column, computer controlled universal materials testing machine using Testometric’s feature-rich winTest™ Analysis software running under the Windows™ operating system. Test setups are fully configurable and simple or more complex multi-stage test routines are controlled using the standard PC serial interface.
CHRocodile S
close
CHRocodile S
32
Optical Sensor for Non-contact distance thickness measurement The new sensor CHRocodile S, with its modern design, represents the latest generation of optical distance and thickness measuring devices. It is applicable for highly accurate distance and topography measurements as well for measuring optically transparent materials (glass, films, varnish etc.). Its low price now enables customers of all budgets to benefit from the numerous advantages of the CHRocodile sensors.
Computerized Tensile Testing Machine
close
Computerized Tensile Testing Machine
20kN Model
The M350-20 range of twin column, computer controlled universal materials testing machine using Testometric’s feature-rich winTest™ Analysis software running under the Windows™ operating system. Test setups are fully configurable and simple or more complex multi-stage test routines are controlled using the standard PC serial interface.
Limiting Oxygen Index Analyzer (LOI)
close
Limiting Oxygen Index Analyzer (LOI)
LOI
windows 7 pro to buy Easy to Operate – User needs only to ignite specimen and adjust gas flow Flexible Sample Testing – Specimens may be in rod, film or composite form Uniform Combustion Atmosphere – Nitrogen and oxygen are fully mixed in a special dispersion chamber and glass bead bed before entering column Precision Gas…
PermMate oxygen permeation analyzer
close
PermMate oxygen permeation analyzer
27
Versatile and patented method of oxygen permeability analysis for packages, bottles and film The PermMate utilizes a patented method of oxygen permeation analysis of sealed packages. The permeability and the barrier qualities of a foil changes when it is shaped into a finished package and as a result the shelf life of the food products can be affected. Therefore, it is important that the package is tested at this stage. This oxygen permeation analyzer is designed to measure the oxygen ingress of the package and to calculate th…
CHRocodile IT
close
CHRocodile IT
IT
The new CHRocodile IT measuring system registers the silicon thickness with just one sensor The new CHRocodile IT from Precitec Optronik now offers very simple and at the same time highly accurate layer thickness measurement for wafers and chips. It is capable of contact-free silicon scanning with just one measuring point and can measure a wafer precisely to a thickness of 1 mm.
Laboratory Mixing Extruder
close
Laboratory Mixing Extruder
LME
R & D tool Uses as little as a few grams of material Three-part system: Extruder, Optional Take Up, and Chopper Accessories Standard configuration provides rod header with replaceable 1/8” (.3175cm) orifice Four optional headers available (ribbon, spinerette, tube and wire coating rod) Two separate temperature controls: rotor heater and header heater Short residence time �…
Computer Based Tensile Testing Machine
close
Computer Based Tensile Testing Machine
25kN Model
The M500-25 range of twin column, computer controlled universal materials testing machine using Testometric’s feature-rich winTest™ Analysis software running under the Windows™ operating system. Test setups are fully configurable and simple or more complex multi-stage test routines are controlled using the standard PC serial interface.
Water Vapor Permeation Analyzer
close
Water Vapor Permeation Analyzer
7000
Modular systems for precision water vapor permeabilty testing of packaging film barriers. The 7000 water vapor analyzer range utilises the sensitive and stable P2O5 sensor for absolute moisture measurement. These water vapor analyzers offer a wide measurement range of 0.002-1000 g/m²/day and precision temperature, humidity and flow control. Providing accurate and repeatable results for research and development testing of water transmission rate (wvtr) in both current and newly formulated packaging film materials and fast testing for Quality Control. All Systech Il…
CHRocodile M4
close
CHRocodile M4
M4
Contact-free measurement of bottle thickness and roundness with the new CHRocodile M4 The new thickness measurement system CHRocodile M4 from Precitec Optronik now provides a particularly economical solution for inline inspections during the production of bottles and container glass.
CHRocodile X
close
CHRocodile X
33
Pushed by Xenon If your target is topographic evaluation of large areas: try the high speed sensor CHRocodile X. This task is perfectly fulfilled up to 14 times faster compared to the former model CHR 150 E. With its Xenon technology the CHRocodile X achieves a significantly higher light emission than with the previously used Halogen bulbs in the CHR 150 E. This leads to the maximum scanning rate of 14 kHz on almost all surfaces.
Electronic Block- Reblock Tester
close
Electronic Block- Reblock Tester
Dynisco BRB
The BRB was designed to measure the undesired static adhesion which can exist between layers of certain types of plastic films. The Dynisco BRB utilizes a compact mechanical balancing system that incrementally adds weight equivalent to 90 ml per minute of water. Through use of this system, the BRB is able to increase the precision and speed of blocking tests and meets or exceeds all conditions specified by ASTM D3354. The BRB Tester features a magnetic clamp to securely hold the sample in place, eliminating the ne…
Water Vapor Permeation Analyzer
close
Water Vapor Permeation Analyzer
Lyssy L80-5000
Modular systems for precision water vapor permeabilty testing of packaging film barriers. The 7000 water vapor analyzer range utilises the sensitive and stable P2O5 sensor for absolute moisture measurement. These water vapor analyzers offer a wide measurement range of 0.002-1000 g/m²/day and precision temperature, humidity and flow control. Providing accurate and repeatable results for research and development testing of water transmission rate (wvtr) in both current and newly formulated packaging film materials and fast testing for Quality Control. Al…
Computerized Universal Tensile Testing Machine
close
Computerized Universal Tensile Testing Machine
30kN Model
The M500-30 range of twin column, computer controlled universal materials testing machine using Testometric’s feature-rich winTest™ Analysis software running under the Windows™ operating system. Test setups are fully configurable and simple or more complex multi-stage test routines are controlled using the standard PC serial interface.
Computer Controlled Universal Testing Machine
close
Computer Controlled Universal Testing Machine
50kN Model
The M500-50 computer controlled universal materials testing machine using Testometric’s feature-rich winTest™ Analysis software running under the Windows™ operating system. Test setups are fully configurable and simple or more complex multi-stage test routines are controlled using the standard PC serial interface.
4000 Measurements Per Second
close
4000 Measurements Per Second
34
The new generation of optical sensors from Precitec Optronik “CHRocodile” sets new standards in optical distance and thickness measurements. With it?s fast 4 kHz technology the CHRocodile provides advantages particularly in topographic evaluations on high reflecting surfaces: The duration of measurement is reduced by factor 4. The CHRocodile E is an advancement of the reliable sensor CHR 150 E. The method of mea…
CHRocodile IT 18 – 3000
close
CHRocodile IT 18 – 3000
33
Application: thickness measurement of wafer, PET-bottles and plastic foils The new optical sensor for thickness measurement from Precitec Optronik is the CHRocodile IT 18 – 3000. The CHRocodile IT 18 – 3000 covers the largest measuring range in the IT series of proven and highly precise CHRocodile sensors. The measuring range in air extends between 18 – 3000 µm. This corresponds to a measuring range of 5 – 800 µm in silicon (refractive index n ≈ 3.6). For film or plastic (n ≈ 1.5) the measuring range is between 12 and 2000 µm.
Universal Material Testing Equipment
close
Universal Material Testing Equipment
100kN Model
The FS100 computer controlled universal materials testing machine using Testometric’s feature-rich winTest™ Analysis software running under the Windows™ operating system. Test setups are fully configurable and simple or more complex multi-stage test routines are controlled using the standard PC serial interface.
Computerized Compression Testing Machine
close
Computerized Compression Testing Machine
150kN Model
The FS150 computer controlled universal materials testing machine using Testometric’s feature-rich winTest™ Analysis software running under the Windows™ operating system. Test setups are fully configurable and simple or more complex multi-stage test routines are controlled using the standard PC serial interface.
Universal Testing Machine
close
Universal Testing Machine
300kN Model
The FS300 computer controlled universal materials testing machine using Testometric’s feature-rich winTest™ Analysis software running under the Windows™ operating system. Test setups are fully configurable and simple or more complex multi-stage test routines are controlled using the standard PC serial interface.
Universal Testing Machine
close
Universal Testing Machine
500kN Model
The FS500 computer controlled universal materials testing machine using Testometric’s feature-rich winTest™ Analysis software running under the Windows™ operating system. Test setups are fully configurable and simple or more complex multi-stage test routines are controlled using the standard PC serial interface.
Universal Testing Machine
close
Universal Testing Machine
600kN Model
The FS600 computer controlled universal materials testing machine using Testometric’s feature-rich winTest™ Analysis software running under the Windows™ operating system. Test setups are fully configurable and simple or more complex multi-stage test routines are controlled using the standard PC serial interface
Horizontal Tester
close
Horizontal Tester
15
Testometric can supply versions of their AT & CT machines suitable for testing in a horizontal mode. Applications usually involve specimens where long lengths need to be tested such as control cables, rope, cord, electrical cables etc. Machines are available with frames capable of testing specimens up to 20 metres long.
Wide Frame Testing Systems
close
Wide Frame Testing Systems
16
Testometric produce wide frame versions of their AT and CT universal strength testing machine. They can be tailored to suit customer’s specific applications.
Box Compression Model
close
Box Compression Model
17
Box compression tester with integral Pc and software dedicated to testing corrugated board boxes and cartons.
Small Box Compression Tester
close
Small Box Compression Tester
18
Dedicated compression tester for corrugated board boxes, cartons, containers, drums and other packaging materials.
Dual Test Systems
close
Dual Test Systems
19
Standard and wide frame models are available with dual or triple test stations. These models are particularly useful for users who test a varied and consistently changing range of products that involve different grips and load cells etc. A second test station can be added to FS150 and FS300 models, this is situated at the side of the main loading frame and can be fitted with load cells up to a maximum capacity of 25kN. The system is ideal where both high and relatively low strength materials need to be tested in that the correct load cells and grips are always fitted ready for testing.
Fibre Micro Tester
close
Fibre Micro Tester
20
The M250-FT CT & AT precision low capacity computer controlled testing machine. The main areas of application include fibre testing, electronic components, circuit boards, small components etc.
Foam Seat Tester
close
Foam Seat Tester
21
A special wide frame machine for testing foam and seating. Used extensively in the automotive seat and furniture industry. The machine has special internal software for conducting multiple stage cyclic and indentation hardness testing.
Glass Tester
close
Glass Tester
22
Glass has a very high compressive structure strength and consequently always fails under tensile stress. Since glass in buildings is very rarely used in direct tension, the most important property is the tensile bending strength. The EN standard calls for a four-point bend test with spans of 1000mm and 200mm and a sample width of 360mm.
Large Sheet Tester
close
Large Sheet Tester
23
Special testers are available to conduct flexural tests on full sheet materials such as construction panels, insulation board, roofing panels and similar products.
Long Frame Tester
close
Long Frame Tester
24
Testometric produce extended frame versions of their AT and CT universal strength testing machine. Depending on the application and length of frame required we can position the control console accordingly to maintain correct working height.
Multi Station Tester
close
Multi Station Tester
25
The M500-ATMS is a modified version of our standard M500-AT machine. It has 5 stations where tests can be conducted simultaneously. The colour display shows plots of all 5 tests in real time, calculated results and statistics. A printer can be connected to produce a full test report. The machine is particularly useful for companies who are involved in volume testing. It greatly reduces test time and is extremely cost effective and space efficient when compared with using multiple machines.
Spring Tester
close
Spring Tester
26
The Testometric AT-S and CT- S models are a range of dedicated spring testers based on the AT and CT Universal testing machines. They have internal capacity to store controlled test methods for several thousand spring types. These test methods are stored and recalled for use under a simple spring reference. Each method will control the whole test automatically taking the spring to desired positions and producing the calculations and results required.




RFQ Request For Quotation
Get Quotes For Your Buying Requirement. Tell Suppliers What You Need.
I agree to abide by all the Terms and Conditions of tradeindia.com
FEDERAL INDIA TRADING COMPANY All Rights Reserved.